Beam and image experiment of beam deflection electron gun for distributed X-ray sources

Distributed X-ray sources comprise a single vacuum chamber containing multiple X-ray sources that are triggered and emit X-rays at a specific time and location. This process facilitates an application for innovative system concepts in X-ray and computer tomography. This paper proposes a novel electron beam focusing, shaping,and deflection electron gun for distributed X-ray sources.The electron gun uses a dispenser cathode as an electron emitter, a mesh grid to control emission current, and two electrostatic lenses for beam shaping, focusing, and deflection. Novel focusing and deflecting electrodes were designed to increase the number of focal spots in the distributed source. Two identical half-rectangle opening electrodes are controlled by adjusting the potential of the two electrodes to control the electron beam trajectory, and then, multifocal spots are obtained on the anode target. The electron gun can increase the spatial density of the distributed X-ray sources, thereby improving the image quality. The beam experimental results show that the focal spot sizes of the deflected(deflected amplitude 10.5 mm)and non-deflected electron beams at full width at half maximum are 0.80 mm 90.50 mm and 0.55 mm 90.40 mm, respectively(anode voltage 160 kV; beam current 30 mA). The imaging experimental results demonstrate the excellent spatial resolution and time resolution of an imaging system built with the sources, which has an excellent imaging effect on a field-programmable gate array chip and a rotating metal disk.     

基于安全围壁的浮动堆旁路泄漏设计研究

基于陆上核电厂二次安全壳的概念，引入了浮动堆安全围壁的构想，提出了“安全壳+安全壳围壁+堆舱”的放射性包容模式。研究了评价安全围壁的旁路泄漏设计思路，提出识别旁路泄漏途径和确定旁路泄漏率的方法。给出了安全围壁负压的设计依据，为后期浮动堆通风系统的设计提供参考。      

Ti70合金板的组织与力学性能的各向异性

通过拉伸及低温冲击试验、光学显微镜、扫描电镜及X射线衍射仪,对Ti70合金板的组织与力学性能的各向异性进行了研究。结果表明,Ti70合金板热轧及退火后组织未出现明显差异,退火过程中主要以回复为主,但在高密度位错的剪切带上出现了一定数量的再结晶晶粒。退火态Ti70合金板横向屈服强度及低温冲击吸收能量都高于纵向,但抗拉强度低于纵向,表现出了明显的各向异性。退火后Ti70合金板形成了较强的{0002}基面织构,其晶面法向向RD方向(纵向)偏转±30°,向TD(横向)方向偏转±41°。由于基面织构更向RD方向集中,因此造成了Ti70合金板力学性能的各向异性。     

发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。     

Copper-doped flower-like molybdenum disulfide/bismuth sulfide photocatalysts for enhanced solar water splitting

A facile synthesis approach to fabricate Cu-doped MoS₂/Bi₂S₃ (Cu-MoS₂/Bi₂S₃) photocatalysts is reported. The photocatalyst samples with varying amounts of Cu are applied in the photocatalytic splitting of water to produce H₂ under the irradiation of simulated solar light. The Cu-MoS₂/Bi₂S₃ photocatalysts with an optimum Cu loading of 20 mol% exhibited high photocatalytic performance, achieving a total H₂ yield of 32.4 μmol/h after 6 h of reaction. The photoactivity of the Cu-doped sample was shown to have risen more than 40% than that of pure MoS₂/Bi₂S₃. The improved performance is attributed to the impurity states generated within Cu-doped MoS₂, which serve as trapping sites for photogenerated electrons. The effective charge transfer mechanism achieved was evidenced by photoelectrochemical measurements. Based on the experimental results obtained, a plausible mechanism for the photocatalytic process associated with Cu-MoS₂/Bi₂S₃ was proposed.     

A Flexi-PEGDA Upconversion Implant for Wireless Brain Photodynamic Therapy

Near-infrared (NIR) activatable upconversion nanoparticles (UCNPs) enable wireless-based phototherapies by converting deep-tissue-penetrating NIR to visible light. UCNPs are therefore ideal as wireless transducers for photodynamic therapy (PDT) of deep-sited tumors. However, the retention of unsequestered UCNPs in tissue with minimal options for removal limits their clinical translation. To address this shortcoming, biocompatible UCNPs implants are developed to deliver upconversion photonic properties in a flexible, optical guide design. To enhance its translatability, the UCNPs implant is constructed with an FDA-approved poly(ethylene glycol) diacrylate (PEGDA) core clad with fluorinated ethylene propylene (FEP). The emission spectrum of the UCNPs implant can be tuned to overlap with the absorption spectra of the clinically relevant photosensitizer, 5-aminolevulinic acid (5-ALA). The UCNPs implant can wirelessly transmit upconverted visible light till 8 cm in length and in a bendable manner even when implanted underneath the skin or scalp. With this system, it is demonstrated that NIR-based chronic PDT is achievable in an untethered and noninvasive manner in a mouse xenograft glioblastoma multiforme (GBM) model. It is postulated that such encapsulated UCNPs implants represent a translational shift for wireless deep-tissue phototherapy by enabling sequestration of UCNPs without compromising wireless deep-tissue light delivery.     

Nanoporous copper sonocatalysts prepared by dealloying Cu–Al–Ti amorphous ribbons

ABSTRACT

Nanoporous copper (NPC) with a controllable ligament width was prepared by chemically dealloying Cu₄₅Al₄₅Ti₁₀ amorphous ribbons in dilute HCl solution. X-ray diffraction and scanning electron microscopy analysis confirmed the 3D, bicontinuous, nanoporous structure constituting fcc-Cu ligaments of 39–79?nm thickness. The coarsening of NPC ligaments increased significantly with an increase of HCl concentration, reaction temperature or time. The surface diffusivity and activation energy of NPC were also calculated. Finally, the catalytic activity of NPC was validated with the ultrasound and H₂O₂-assisted degradation of methyl orange (MO), where 99% MO was degraded within 15?min.